DELUXE HEAVY-DUTY LEVER-TYPE BALL JOINT AND TIE ROD END REMOVER Designed to fit areas with restricted space. Powerful lever action removes stubborn ball joints easily. For cars and 1/2-ton trucks 11/16" opening. 1-1/2" seat. No hammering required. Won't damage grease cups.

BALL JOINT AND 4WD SERVICE TOOL KIT The most complete kit available! Excellent heavy-duty tools for installing/removing ball joints universal joints and truck anchor pins. For 2WD and 4WD vehicles. Works on rusted and corroded parts too! Kit includes "C" frame press with screw assembly; 3 receiver tubes (2-3/4" x 3" 2-1/4" x 2-1/2" and 1-3/4" x 2"); installation/removal adapters; compartmented blow-molded carrying case. Removes/installs press-fit parts on or off vehicle. Affordable and strong (hardened top-quality steel tools stand up to toughest conditions).

AIR DIE GRINDER/CUTOFF TOOL KIT 1/4" Collet accepts all 1/4" shank accessories - 22000 rpm. Converts easily into a cut-off tool (with steel safety shield) to cut steel rod sheet metal or muffler clamps. Kit includes 5 grinding stones two 3" diam. cutting discs (accepts all 3" diam. discs) hex key wrench 3 special wrenches 2 adapters and heavy-duty plastic storage case with compartments and built-in carry handle.

ELECTRICAL HARNESS RELEASE TOOL SET Save time and trouble. Easily disconnect electrical connectors. Disconnect electrical connectors easily without breaking them no matter where they're located. Separate puller and pusher tools provide access to the electrical connectors on American vehicles ensuring a trouble-free release. One-hand operation. Made of steel. Set of 2.

AIR TOOL FILTER/REGULATOR/ LUBRICATOR WITH GAUGE Easy-to-clean filter Gauge reads 0- to160-psi. Regulates outlet pressure from 5- to 125-psi. Lubricator which can be shut off completely adds an oil mist to the air supply. 3/8" inlet/outlet ports. Includes reducers for 1/4" fittings mounting bracket and hardware.

AIR TOOL HOSE Oil and chemical-resistant nylon Each end has 360° swivel 1/4" NPT brass male fitting and spring guard to prevent airflow restriction Stretches up to 25 ft. and then snaps back into position without tangling 200 psi capacity. 1/4"ID

Sprays enamel, lacquer, stain or acrylic for customizing and restoring automobiles, trucks and motorcycles. Average 6.8 SCFM at 40 PSI. Fluid and pattern control, non-bleeder, pressure and siphon control.

Heavy-duty construction for automotive, farm and light truck work.

Sturdy, durable, allows safe access to underside of vehicle. 17 degree incline for low clearance vehicles. Core-Trac non-skid feet. Durable structural foam plastic design.

The Spark Plug Wire Tester quickly locates faulty plug wires without any shock hazard. Now you can check spark plug wires without actually piercing the wire. Light flashes indicating sound wire.

WINDSHIELD WIPER ARM REMOVER Removes windshield wiper arm with spring-loaded retainers. No damage to vehicle.

32-BLADE GAUGE 3-5/16"L blades. Sizes .0015" through .035" plus .010" (brass blade) for transistorized engines.

OIL PUMP PULLER For quick easy removal of oil pump without case damage.

CLUTCH PLATE HUB REMOVAL/INSTALLATION KIT For air conditioner compressors. A Classic Tool Design Inc. tool. Kit includes puller disk with tapped holes 3 puller bolts 3 removal nuts 4 removal adapters 3 replacement adapters master arbor for use with all adapters and thrust bearing. For use with the following compressors: Bosch; Chrysler C171; Diesel Kiki; Ford FS6 6P148 HR980; General Motors A6 R4 DA6 V5; Mitsubishi; Nippondenso; Sanden.